Dry Charged Maintenance Free Lead Acid Battery
Motorcycle Battery
Key Features of Our Dry-Charged Battery
- 100% Pre-delivery inspection to ensure stable quality and reliable performance.
- Pb-Ca grid alloy battery plate, low water loss, and stable quality low self-discharge rate.
- With heat sealing technology, good sealing property.
- Low internal resistance, good high rate discharge performance.
- Excellence high-and-low temperature performance, working temperature ranging from -30°C to 55°C.
- Design float service life: 3-5 years.
Dry Charged Safe Use Precautions
I. Warning
- The electrolyte inside the battery is corrosive and may damage metal, cotton products, and stone. Handle the battery properly.
- Do NOT place the battery on its side or upside down to prevent acid leakage.
- Hydrogen gas may be generated during battery operation and charging. If exposed to fire or sparks, it may cause an explosion. Please observe the following precautions:
- Use and maintain the battery in a well-ventilated area.
- Keep sparks and open flames away during battery maintenance.
- If the battery is charged outside the vehicle, do not install it immediately after charging. Let it rest for at least 10 minutes to allow hydrogen gas to dissipate.
- After riding, do not remove the battery immediately. Let it rest for at least 10 minutes.
- During charging, the ambient temperature should not exceed 45°C. If it does, cool the battery with water or reduce the charging current and voltage.
- Do NOT place metal tools or conductive materials near the terminals to avoid short-circuiting.
- Do NOT strike the terminals with a hammer during battery installation.
- Handle the battery carefully during transportation to avoid impact or damage.
II. Dry charged Installation and Maintenance
- Connect the positive terminal first. Do NOT reverse the polarity, otherwise the motorcycle’s electrical equipment may be damaged.
- Activation Notice:
- Some batteries may not be activated immediately due to differences in vehicle performance. Start the engine several times or gently apply the throttle to help activate the battery more easily.
- Manual activation is recommended to ensure the exact activation date is recorded.
- During acid filling, wear acid-resistant clothing, rubber boots, safety goggles, and rubber gloves. If acid splashes onto skin or clothing, rinse immediately with a large amount of water. Seek medical attention if necessary.
- Do NOT over-discharge the battery. Recharge the battery promptly after it has been discharged.
- Disconnect the negative terminal if the motorcycle will not be used for a long period.
- Do NOT check whether the battery has power by short-circuiting the terminals.
- Regularly check the terminal connections and ensure the terminals are clean to maintain good contact.
- Store the battery in a dry, well-ventilated place at 5–25°C, away from direct sunlight. Keep the battery at least 2 meters away from heat sources. Check and maintain the battery regularly.
Related Products
| Type | Model | Voltage (V) | Capacity (Ah) | Hour Rate (HR) | Dimension±2 (mm) | Polarity | Weight±3% (KG) | Acid Volume (L) | Terminal | Regular Charge Current (A) | CCA(-18°C) | Datasheet |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Heavy Duty | 6N4-BS | 6 | 4 | 10 | 70*70*96 | - + | 0.5 | 0.12 | (+)90mmCB104 (-)90mmCB104 | 0.4 | 30 | |
| Heavy Duty | UTX2.5L-BS | 12 | 2.5 | 10 | 80*71*103 | - + | 0.73 | 0.15 | (+)100mmCB103 (-)100mmCA103 | 0.25 | 20 | |
| Heavy Duty | YTR4A-BS | 12 | 2.3 | 10 | 113*48*85 | - + | 0.78 | 0.13 | G11 | 0.23 | 30 | |
| Heavy Duty | YT4B-BS | 12 | 2.3 | 10 | 113*38*85.5 | - + | 0.72 | 0.12 | G12 | 0.23 | 30 | |
| Heavy Duty | UTX3L-BS | 12 | 3 | 10 | 99*57*108 | - + | 0.91 | 0.18 | G1 | 0.3 | 30 | |
| Heavy Duty | UTX4L-BS | 12 | 3 | 10 | 113*70*85 | - + | 1.04 | 0.21 | G2 | 0.3 | 45 | |
| Heavy Duty | UTX4L-BS | 12 | 4 | 10 | 113*70*85 | - + | 1.14 | 0.21 | G2 | 0.4 | 50 | |
| Heavy Duty | UTX5L-BS | 12 | 4 | 10 | 113*70*105 | - + | 1.48 | 0.27 | G2 | 0.4 | 70 | |
| Heavy Duty | UTZ5S-BS | 12 | 4 | 10 | 113*70*85 | - + | 1.14 | 0.21 | G2 | 0.4 | 50 | |
| Heavy Duty | UTZ7S-BS | 12 | 6 | 10 | 113*70*105 | - + | 1.56 | 0.24 | G2 | 0.6 | 80 | |
| Heavy Duty | UTZ8S-BS | 12 | 6 | 10 | 113*70*120 | - + | 1.86 | 0.29 | G2 | 0.6 | 100 | |
| Heavy Duty | YT5A-BS | 12 | 5 | 10 | 119*60*128 | + - | 1.43 | 0.32 | G1 | 0.5 | 70 | |
| Heavy Duty | YT5AL-BS | 12 | 5 | 10 | 119*60*128 | - + | 1.43 | 0.32 | G1 | 0.5 | 70 | |
| Heavy Duty | YT5A-BS | 12 | 5 | 10 | 119*60*128 | + - | 1.38 | 0.32 | G1 | 0.5 | 65 | |
| Heavy Duty | YT5AL-BS | 12 | 5 | 10 | 119*60*128 | - + | 1.38 | 0.32 | G1 | 0.5 | 65 | |
| Heavy Duty | UTX7A-BS | 12 | 6 | 10 | 150*87*93 | + - | 1.87 | 0.35 | G3 | 0.6 | 90 | |
| Heavy Duty | UTX7L-BS | 12 | 6 | 10 | 113*70*130 | - + | 1.85 | 0.35 | G2 | 0.6 | 85 | |
| Heavy Duty | UTX6.5L-BS | 12 | 6.5 | 10 | 138*66*100 | - + | 1.54 | 0.27 | G1 | 0.65 | 70 | |
| Heavy Duty | UTX7D-BS | 12 | 7 | 10 | 148*59*130 | + - | 1.81 | 0.45 | G1 | 0.7 | 100 | |
| Heavy Duty | UTX7D-BS | 12 | 7 | 10 | 148*59*130 | + - | 1.76 | 0.45 | G1 | 0.7 | 100 | |
| Heavy Duty | UTX7DL-BS | 12 | 7 | 10 | 148*59*130 | - + | 1.76 | 0.45 | G1 | 0.7 | 100 | |
| Heavy Duty | YT7B-BS | 12 | 6.5 | 10 | 150*65*93 | + - | 1.68 | 0.32 | G13 | 0.65 | 70 | |
| Heavy Duty | YT7B-BS | 12 | 6.5 | 10 | 150*65*93 | + - | 1.68 | 0.32 | G2 | 0.65 | 70 | |
| Heavy Duty | UTX7E-BS | 12 | 6.5 | 10 | 135*75*132 | + - | 2.05 | 0.47 | G2 | 0.7 | 100 | |
| Heavy Duty | UTX7EL-BS | 12 | 7 | 10 | 135*75*132 | - + | 2.05 | 0.47 | G2 | 0.7 | 100 | |
| Heavy Duty | UTX9-BS | 12 | 8 | 10 | 150*87*105 | + - | 2.21 | 0.45 | G3 | 0.8 | 120 | |
| Heavy Duty | YT9B-BS | 12 | 8 | 10 | 150*70*105 | + - | 1.95 | 0.42 | G2 | 0.8 | 90 | |
| Heavy Duty | YT9B-BS | 12 | 8 | 10 | 150*70*105 | + - | 2.05 | 0.42 | G13 | 0.8 | 90 | |
| Heavy Duty | UTZ10S-BS | 12 | 8.6 | 10 | 150*87*95 | + - | 2.57 | 0.43 | G13 | 0.86 | 150 | |
| Heavy Duty | YT9A-BS | 12 | 9 | 10 | 135*75*137 | + - | 2.05 | 0.47 | G1 | 0.9 | 100 | |
| Heavy Duty | YT9AL-BS | 12 | 9 | 10 | 135*75*137 | - + | 2.05 | 0.47 | G1 | 0.9 | 100 | |
| Heavy Duty | YT12A-BS | 12 | 9.5 | 10 | 150*87*105 | + - | 2.31 | 0.45 | G3 | 0.95 | 120 | |
| Heavy Duty | UTX12-BS | 12 | 10 | 10 | 150*87*130 | + - | 3 | 0.61 | G3 | 1 | 140 | |
| Heavy Duty | UTX12L-BS | 12 | 10 | 10 | 150*87*130 | - + | 3 | 0.61 | G3 | 1 | 140 | |
| Heavy Duty | YT12B-BS | 12 | 10 | 10 | 150*70*130 | + - | 2.44 | 0.53 | G2 | 1 | 125 | |
| Heavy Duty | YT12B-BS | 12 | 10 | 10 | 150*70*130 | + - | 2.6 | 0.53 | G13 | 1 | 135 | |
| Heavy Duty | UTZ12S-BS | 12 | 11.2 | 10 | 150*87*110 | + - | 3.04 | 0.57 | G13 | 1.12 | 190 | |
| Heavy Duty | UTZ14S-BS | 12 | 11.2 | 10 | 150*87*110 | + - | 3.04 | 0.57 | G13 | 1.12 | 190 | |
| Heavy Duty | YT14B-BS | 12 | 12 | 10 | 150*70*145 | + - | 2.9 | 0.65 | G2 | 1.2 | 140 | |
| Heavy Duty | UTX14-BS | 12 | 12 | 10 | 150*87*145 | + - | 3.43 | 0.68 | G3 | 1.2 | 160 | |
| Heavy Duty | UTX14L-BS | 12 | 12 | 10 | 150*87*145 | - + | 3.43 | 0.68 | G3 | 1.2 | 160 | |
| Heavy Duty | UTX14AH-BS | 12 | 12 | 10 | 135*87*165 | + - | 3.22 | 0.65 | G3 | 1.2 | 160 | |
| Heavy Duty | UTX14AHL-BS | 12 | 12 | 10 | 135*87*165 | - + | 3.22 | 0.65 | G3 | 1.2 | 160 | |
| Heavy Duty | UTX15L-BS | 12 | 13 | 10 | 175*87*130 | - + | 3.6 | 0.72 | G2 | 1.3 | 190 | |
| Heavy Duty | UTX16-BS | 12 | 14 | 10 | 150*87*161 | + - | 3.85 | 0.78 | G3 | 1.4 | 180 | |
| Heavy Duty | UTX16-BS-1 | 12 | 14 | 10 | 150*87*161 | + - | 3.85 | 0.78 | G4 | 1.4 | 180 | |
| Heavy Duty | UTX20-BS | 12 | 18 | 10 | 175*87*155 | + - | 4.57 | 0.91 | G3 | 1.8 | 240 | |
| Heavy Duty | UTX20L-BS | 12 | 18 | 10 | 175*87*155 | - + | 4.57 | 0.91 | G3 | 1.8 | 240 | |
| Heavy Duty | UTX19CL-BS | 12 | 19 | 10 | 175*100*175 | - + | 5 | 1.03 | G3 | 1.9 | 240 | |
| Heavy Duty | UTX18L-BS | 12 | 20 | 10 | 205*87*162 | - + | 4.6 | 1.19 | G2 | 2 | 240 | |
| Heavy Duty | UTX18L-BS | 12 | 24 | 10 | 205*87*162 | - + | 5.35 | 1.08 | G2 | 2.4 | 300 | |
| Heavy Duty | UTX30L-BS | 12 | 28 | 10 | 167*127*175 | - + | 5.6 | 1.2 | G2 | 2.8 | 280 |