Intelligent Detected Motorcycle Battery
Motorcycle Battery
With built-in chip, iGEL battery has self-test function for users to real-time monitors battery capacity and to maintain battery when battery capacity is low, therefore battery service life can be prolonged.
Push-to-open Lid Cover
Adding acid for maintenance by opening lid cover to prolong the battery service life.
Injected with Gel electrolyte instead of acid, the battery is of super performance
- Higher capacity.
- Good performance in the low temperatures, can meet requirements of starting currents in -30℃ to -50℃.
- Stable characteristic in high temperatures, can meet requirements of its usage in temperature of 65℃ and even higher.
- Longer cycle service life than normal lead acid battery type.
iGEL Safe Use Precautions
I. Warning
- The electrolyte inside the battery is corrosive and may damage metal, cotton products, and stone. Handle the battery properly.
- Do NOT place the battery on its side or upside down to prevent acid leakage.
- Hydrogen gas may be generated during battery operation and charging. If exposed to fire or sparks, it may cause an explosion. Please observe the following precautions:
- Use and maintain the battery in a well-ventilated area.
- Keep sparks and open flames away during battery maintenance.
- If the battery is charged outside the vehicle, do not install it immediately after charging. Let it rest for at least 10 minutes to allow hydrogen gas to dissipate.
- After riding, do not remove the battery immediately. Let it rest for at least 10 minutes.
- During charging, the ambient temperature should not exceed 45°C. If it does, cool the battery with water or reduce the charging current and voltage.
- Do NOT place metal tools or conductive materials near the terminals to avoid short-circuiting.
- Do NOT strike the terminals with a hammer during battery installation.
- Handle the battery carefully during transportation to avoid impact or damage.
iGEL Installation and Maintenance
- Connect the positive terminal first. Do NOT reverse the polarity, otherwise the motorcycle’s electrical equipment may be damaged.
- Activation Notice:
- Some batteries may not be activated immediately due to differences in vehicle performance. Start the engine several times or gently apply the throttle to help activate the battery more easily.
- Manual activation is recommended to ensure the exact activation date is recorded.
- During acid filling, wear acid-resistant clothing, rubber boots, safety goggles, and rubber gloves. If acid splashes onto skin or clothing, rinse immediately with a large amount of water. Seek medical attention if necessary.
- Do NOT over-discharge the battery. Recharge the battery promptly after it has been discharged.
- Disconnect the negative terminal if the motorcycle will not be used for a long period.
- Do NOT check whether the battery has power by short-circuiting the terminals.
- Regularly check the terminal connections and ensure the terminals are clean to maintain good contact.
- Store the battery in a dry, well-ventilated place at 5–25°C, away from direct sunlight. Keep the battery at least 2 meters away from heat sources. Check and maintain the battery regularly.
Related Products
| Type | Model | Voltage (V) | Capacity (Ah) | Hour Rate (HR) | Dimension±2 (mm) | Polarity | Weight±3% (KG) | Terminal | Regular Charge Current (A) | Meter CCA (25±5°C) | CCA (-18°C) | Datasheet |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| YB Type | YB2.5L-BS(iGEL) | 12 | 2.5 | 10 | 80*77*105 | - + | 1.03 | W | 0.25 | N/A | 20 | |
| YB Type | YB3L-BS(iGEL) | 12 | 3 | 10 | 98*56*109 | - + | 1.19 | C6 | 0.3 | 80 | 35 | |
| YB Type | YB5L-BS(iGEL) | 12 | 5 | 10 | 119*60*129 | - + | 1.77 | C6 | 0.5 | 155 | 55 | |
| YB Type | YB5L-BS(iGEL) | 12 | 5 | 10 | 119*60*129 | - + | 1.86 | C6 | 0.5 | 80 | 50 | |
| YB Type | YB6.5L-BS(iGEL) | 12 | 6.5 | 10 | 138*65*100 | - + | 1.98 | C8 | 0.65 | 155 | 75 | |
| YB Type | YB6.5L-BS(iGEL) | 12 | 6.5 | 10 | 138*65*100 | - + | 2.16 | C8 | 0.65 | 140 | 75 | |
| YB Type | YB7B-BS(iGEL) | 12 | 7 | 10 | 148*60*128 | + - | 2.21 | C7 | 0.7 | 140 | 75 | |
| YB Type | YB7BL-BS(iGEL) | 12 | 7 | 10 | 148*60*128 | - + | 2.21 | C7 | 0.7 | 140 | 75 | |
| YB Type | YB7-BS(iGEL) | 12 | 8 | 10 | 137*76*128 | + - | 2.65 | C7 | 0.8 | 140 | 85 | |
| YB Type | YB7L-BS(iGEL) | 12 | 8 | 10 | 137*76*128 | - + | 2.65 | C7 | 0.8 | 140 | 85 | |
| YB Type | YB9-BS(iGEL) | 12 | 9 | 10 | 137*76*128 | + - | 2.7 | C7 | 0.9 | 140 | 85 | |
| YB Type | YB9-BS(iGEL) | 12 | 9 | 10 | 137*76*128 | + - | 2.8 | C7 | 0.9 | 160 | 100 | |
| YB Type | YB9-BS(iGEL) | 12 | 9 | 10 | 137*76*128 | + - | 2.95 | C7 | 0.9 | 180 | 110 | |
| YB Type | YB10L-BS(iGEL) | 12 | 10 | 10 | 132*88*145 | - + | 3.45 | C9 | 1 | 230 | 120 | |
| YB Type | YB12A-BS(iGEL) | 12 | 12 | 10 | 134*78*156 | + - | 3.63 | Z1 | 1.2 | 240 | 140 | |
| YB Type | YB12AL-BS(iGEL) | 12 | 12 | 10 | 134*78*156 | - + | 3.63 | Z1 | 1.2 | 240 | 140 | |
| YB Type | YB14-BS(iGEL) | 12 | 14 | 10 | 132*88*163 | + - | 4.54 | Z1 | 1.4 | 285 | 185 | |
| YB Type | YB14L-BS(iGEL) | 12 | 14 | 10 | 132*88*163 | - + | 4.54 | Z1 | 1.4 | 285 | 185 | |
| YB Type | YB16L-BS(iGEL) | 12 | 19 | 10 | 173*100*152 | - + | 6.15 | Z2 | 1.9 | 390 | 240 | |
| YB Type | YB16CL-BS(iGEL) | 12 | 19 | 10 | 173*100*175 | - + | 6.25 | C9 | 1.9 | 320 | 240 | |
| UT Type | UTZ5S(iGEL) | 12 | 4 | 10 | 113*70*87 | - + | 1.3 | C8 | 0.4 | 115 | 45 | |
| UT Type | UTZ5S(iGEL) | 12 | 4 | 10 | 113*70*87 | - + | 1.4 | C8 | 0.4 | 120 | 50 | |
| UT Type | UTZ7S(iGEL) | 12 | 6 | 10 | 113*70*107 | - + | 2.02 | C8 | 0.6 | 150 | 85 | |
| UT Type | UTZ7V(iGEL) | 12 | 7 | 10 | 113*70*121 | - + | 2.28 | C8 | 0.7 | 150 | 100 | |
| UT Type | UTZ10S(iGEL) | 12 | 8.6 | 10 | 150*86*94 | + - | 2.85 | Z1 | 0.86 | 220 | 120 | |
| UT Type | UTZ12S(iGEL) | 12 | 11.2 | 10 | 150*86*111 | + - | 3.36 | Z1 | 1.12 | 200 | 130 | |
| UT Type | UTZ14S(iGEL) | 12 | 11.2 | 10 | 150*86*111 | + - | 3.52 | Z1 | 1.12 | 230 | 150 | |
| UT Type | UTX4L-BS(iGEL) | 12 | 4 | 10 | 113*70*85 | - + | 1.3 | C8 | 0.4 | 115 | 45 | |
| UT Type | UTX4L-BS(iGEL) | 12 | 4 | 10 | 113*70*85 | - + | 1.4 | C8 | 0.4 | 120 | 50 | |
| UT Type | UTX5L-BS(iGEL) | 12 | 5 | 10 | 113*70*107 | - + | 1.64 | C8 | 0.5 | 125 | 55 | |
| UT Type | UTX5L-BS(iGEL) | 12 | 5 | 10 | 113*70*107 | - + | 1.79 | C8 | 0.5 | 130 | 70 | |
| UT Type | YT7B-4(iGEL) | 12 | 6.5 | 10 | 150*65*94 | + - | 2.15 | C8 | 0.65 | 150 | 80 | |
| UT Type | UTX7L-BS(iGEL) | 12 | 7 | 10 | 113*70*130 | - + | 2.15 | C8 | 0.7 | 135 | 75 | |
| UT Type | UTX7L-BS(iGEL) | 12 | 7 | 10 | 113*70*130 | - + | 2.24 | C8 | 0.7 | 140 | 85 | |
| UT Type | UTX7A-BS(iGEL) | 12 | 7 | 10 | 150*86*94 | + - | 2.4 | C9 | 0.7 | 180 | 90 | |
| UT Type | UTX7A-BS(iGEL) | 12 | 7 | 10 | 150*86*94 | + - | 2.48 | C9 | 0.7 | 185 | 100 | |
| UT Type | YT9B-4(iGEL) | 12 | 8 | 10 | 150*70*105 | + - | 2.61 | C9 | 0.8 | 185 | 100 | |
| UT Type | UTX9-BS(iGEL) | 12 | 9 | 10 | 150*86*107 | + - | 2.93 | C9 | 0.9 | 180 | 120 | |
| UT Type | YT12A-BS(iGEL) | 12 | 0.95 | 10 | 150*86*107 | + - | 3.13 | Z1 | 0.95 | 200 | 120 | |
| UT Type | YT12A-BS(iGEL) | 12 | 10 | 10 | 150*86*107 | + - | 3.32 | Z1 | 1 | 245 | 135 | |
| UT Type | YT12B-4(iGEL) | 12 | 10 | 10 | 150*70*130 | + - | 3.12 | C9 | 1 | 185 | 100 | |
| UT Type | UTX12-BS(iGEL) | 12 | 10 | 10 | 150*86*130 | + - | 3.29 | C9 | 1 | 180 | 100 | |
| UT Type | UTX12-BS(iGEL) | 12 | 12 | 10 | 150*86*130 | + - | 3.87 | Z1 | 1.2 | 210 | 140 | |
| UT Type | UTX12-BS(iGEL) | 12 | 12 | 10 | 150*86*130 | + - | 4.12 | Z1 | 1.2 | 240 | 165 | |
| UT Type | UTX14-BS(iGEL) | 12 | 12 | 10 | 150*86*145 | + - | 4.4 | Z1 | 1.2 | 220 | 150 | |
| UT Type | UTX14L-BS(iGEL) | 12 | 12 | 10 | 150*86*145 | - + | 4.4 | Z1 | 1.2 | 220 | 150 | |
| UT Type | UTX14-BS(iGEL) | 12 | 14 | 10 | 150*86*145 | + - | 4.68 | Z1 | 1.4 | 240 | 185 | |
| UT Type | UTX14L-BS(iGEL) | 12 | 14 | 10 | 150*86*145 | - + | 4.68 | Z1 | 1.4 | 240 | 185 | |
| UT Type | UTX16-BS(iGEL) | 12 | 14 | 10 | 150*86*161 | + - | 5 | Z1 | 1.4 | 235 | 165 | |
| UT Type | UTX16L-BS(iGEL) | 12 | 14 | 10 | 150*86*161 | - + | 5 | Z1 | 1.4 | 235 | 165 | |
| UT Type | UTX16-BS(iGEL) | 12 | 16 | 10 | 150*86*161 | + - | 5.3 | Z1 | 1.6 | 255 | 200 | |
| UT Type | UTX16L-BS(iGEL) | 12 | 16 | 10 | 150*86*161 | - + | 5.3 | Z1 | 1.6 | 255 | 200 | |
| UT Type | YT20-4(iGEL) | 12 | 18 | 10 | 177*88*155 | + - | 5.9 | Z2 | 1.8 | 290 | 200 | |
| UT Type | YT20L-4(iGEL) | 12 | 18 | 10 | 177*88*155 | - + | 5.9 | Z2 | 1.8 | 290 | 200 | |
| UT Type | YT20-4(iGEL) | 20 | 18 | 10 | 177*88*155 | + - | 6.2 | Z2 | 2 | 330 | 240 | |
| UT Type | YT20L-4(iGEL) | 20 | 20 | 10 | 177*88*155 | - + | 6.2 | Z2 | 2 | 330 | 240 | |
| UT Type | YT20L-4(iGEL) | 20 | 21 | 10 | 205*91*161 | - + | 6.78 | Z2 | 2.1 | 310 | 220 | |
| UT Type | YT20L-4(iGEL) | 20 | 24 | 10 | 205*91*161 | - + | 7.4 | Z2 | 2.4 | 400 | 320 |